Menu
Your Cart

PIC18F4520 40-pin Flash 32kbyte 40MHz Microcontroller

PIC18F4520 40-pin Flash 32kbyte 40MHz Microcontroller
  • Stock: Out Of Stock
  • Brand: xcluma
  • Model: BE-000702
  • MPN: BE-000702
Rs233.00
(GST +18%Extra)

SPECIFICATIONS:

  • 40-pin Low Power Microcontroller
  • Flash Program Memory: 32 kbytes
  • EEPROM Data Memory: 256 bytes
  • SRAM Data Memory: 1536 bytes
  • I/O Pins: 36
  • Timers: One 8-bit / Three 16-Bit
  • A/D Converter: 10-bit Thirteen Channels
  • PWM: 10-bit Two Modules
  • Enhanced USART: Addressable with RS-485, RS-232 and LIN Support
  • MSSP: SPI and I²C Master and Slave Support
  • External Oscillator: up to 40MHz
  • Internal Oscillator: 8MHz

FEATURES:

  • Power Management Features
    • Run: CPU on, Peripherals on
    • Idle: CPU off, Peripherals on
    • Sleep: CPU off, Peripherals off
    • Ultra Low 50nA Input Leakage
    • Run mode Currents Down to 11 μA Typical
    • Idle mode Currents Down to 2.5 μA Typical
    • Sleep mode Current Down to 100 nA Typical
    • Timer1 Oscillator: 900 nA, 32 kHz, 2V
    • Watchdog Timer: 1.4 μA, 2V Typical
    • Two-Speed Oscillator Start-up
  • Flexible Oscillator Structure:
    • Four Crystal modes, up to 40 MHz
    • 4x Phase Lock Loop (PLL) – Available for Crystal and Internal Oscillators
    • Two External RC modes, up to 4 MHz
    • Two External Clock modes, up to 40 MHz
    • Internal Oscillator Block:
      • Fast wake from Sleep and Idle, 1 μs typical
      • 8 use-selectable frequencies, from 31 kHz to 8 MHz
      • Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL
      • User-tunable to compensate for frequency drift
    • Secondary Oscillator using Timer1 @ 32 kHz
    • Fail-Safe Clock Monitor:
      • Allows for safe shutdown if peripheral clock stops
  • Peripheral Highlights:
    • High-Current Sink/Source 25 mA/25 mA
    • Three Programmable External Interrupts
    • Four Input Change Interrupts
    • Up to 2 Capture/Compare/PWM (CCP) modules, one with Auto-Shutdown (28-pin devices)
    • Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only):
      • One, two or four PWM outputs
      • Selectable polarity
      • Programmable dead time
      • Auto-shutdown and auto-restart
  • Peripheral Highlights (Continued):
    • Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2C™ Master and Slave modes
    • Enhanced Addressable USART module:
      • Supports RS-485, RS-232 and LIN/J2602
      • RS-232 operation using internal oscillator block (no external crystal required)
      • Auto-wake-up on Start bit
      • Auto-Baud Detect
    • 10-Bit, up to 13-Channel Analog-to-Digital (A/D)
    • Converter module:
      • Auto-acquisition capability
      • Conversion available during Sleep
    • Dual Analog Comparators with Input Multiplexing
    • Programmable 16-Level High/Low-Voltage 
    • Detection (HLVD) module:
      • Supports interrupt on High/Low-Voltage Detection
  • Special Microcontroller Features:
    • C Compiler Optimized Architecture:
      • Optional extended instruction set designed to optimize re-entrant code
    • 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical
    • 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical
    • Flash/Data EEPROM Retention: 100 Years Typical
    • Self-Programmable under Software Control
    • Priority Levels for Interrupts
    • 8 x 8 Single-Cycle Hardware Multiplier
    • Extended Watchdog Timer (WDT):
      • Programmable period from 4 ms to 131s
    • Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins
    • In-Circuit Debug (ICD) via Two Pins
    • Wide Operating Voltage Range: 2.0V to 5.5V
    • Programmable Brown-out Reset (BOR) with Software Enable Option

Write a review

Please login or register to review
We are Upgrading...
Sorry, We are currently closed and will reopen on the 21st of July. We apologize for any inconvenience this may cause.