Opt101 Analog Light Sensor Light Intensity Module Monolithic Photodiode 1 orderFeatures:OPT101 is an illuminance photoelectric sensor integrating a photodiode and a specially optimized operational amplifier. Transparent packaging enables the photodiode to have a larger sensing surface, higher sensit..
TCS34725 RGB Color Sensor with IR Filter and White LEDSpecifications:1. Red, Green, Blue (RGB), and White Light Sensing with IR Blocking Filter2. Programmable Analog Gain and Integration Time3. 3,800,000:1 Dynamic Range4. Very High Sensitivity ? Ideally Suited for Operation Behind Dark Glass5. Maska..
DESCRIPTION:BFD-1000 specifically designed for use as a black (white) line finding, especially for complex black and white line, cross black and white line detection, it has 6 high sensitivity infrared sensor (5 road patrol line, a road barrier shield), black and white line to the accurate recog..
Address of this module can be changed. By default, the address is '0100011'.
You can connect the solder bridge in the ADDR box. Then the address becomes '1011100'.
You can also do other configurations. For more information, you can refer to the datasheet.
DESCRIPTION:The LX1972 is a low cost silicon light sensor with spectral response that closely emulates the human eye. Patented circuitry produces peak spectral response at 520nm, with IR response less than ±5%, of the peak response, above 900nm. ..
DESCRIPTION:The CNY70 is a reflective sensor that includes an infrared emitter and phototransistor in a leaded package which blocks visible light.APPLICATION:Optoelectronic scanning and switching devices i.e., index sensing, coded disk scanning etc. (optoelectronic encoder assemblies). L..
DESCRIPTION:This is a small micro switch sensor designed for the Arduino. It could be directly connected to the IO Expansion shield. It integrates the pull-up resistor and the status indicator LED onboard. That makes it easier for testing.The miniature snap-action micro switch with roller lever ..
DESCRIPTION: Fingerprint scanners are awesome. use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you..
DESCRIPTION:GP2Y1010AU0F is a dust sensor by optical sensing system.
An infrared emitting diode (IRED) and an phototransistor are diagonally arranged into this device.
It detects the reflected light of dust in air.
Especially, it is effective to detect very fine particle ..
FEATURES:1. Size: 11 mm x 27 mm2. Low power consumption, the power supply voltage of 2.5 V ~ 5 V, working current is microamps level3. Good linear4. High sensitivity5. High stability6. Wide detection range: 240 nm to 370 nm7. The big Angle: 130 degrees8. Schottky type..
FEATURES:BH1750FVI ROHM chip
Power supply: 3-5 v
Data range: 0-65535
Sensor built-in and bitad converter
Direct digital output, bypassing the complicated calculation, omit calibration
Do not distinguish between ambient light
Close to the visual sensitivity of spectral characterist..
DESCRIPTION:Pulse sensor is used to test the heart rate sensor, students, artists, athletes,
creators, games or mobile terminal developers can develop heart-related and
interactive works. Sensor can be worn on the finger or earlobe, can be connected
with Ard uino line ..
DESCRIPTION:Laser sensor Module
Operating voltage 5V
Output wavelength 650 nm
3 pins module
With fixed bolt hole for easy installationWarning: This is a low power laser device, however as with all laser devices care should be taken when in use. You should never..
DESCRIPTION:PCB size:1.52cm x 2.22cm
Working Voltage: 5 Volt DC
Output: 4-5 Volt DC
On detecting a laser signal, output goes at high level (5V) until laser signal is there.NOTE: This sensor is non-modulator, to be used indoors away from any bright light or direct s..
DESCRIPTION:Odometers are extremely useful for cars, they tell you how far you have gone, wouldn't it be nice if you were able to have a device that does the same for electrical current? The LTC4150 Coulomb Counter Breakout is here to be your odometer for current. If you are wondering: a coulomb..
DESCRIPTION: 1,On-board LM393 voltage comparator chip and HALL sensing probe.2,Support 5V/3.3V voltage input.3, On-board signal output instructions, output the effective signal is low, at the same time indicator light up; Output signal can directly connect with the microcontroller I..
Photosensitive Sensor Module Light Detection Module Features:For Light intensity detected,light brightness sensors,Smart car module
Using the sensitive type photosensitive resistance sensor
Waveform of the comparator output signal is good,strong driving ability
With adjustable potentiomete..
DESCRIPTION:The QRD1114 reflective sensor consists of an infrared (IR) emitting diode and an NPN silicon photodarlington mounted side by side in a black plastic housing.The on-axis radiation of the emitter and the on-axis response of the detector are both perpendicular to the face of the QRD..
DESCRIPTION:This is RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, r..
FEATURES:1, the use of imported groove coupler sensor2, the slot width 5mm.3, the output status indicator lamp output high, output low lights.4, block, output high; no shelter, output low.5, the comparator output signal clean, good waveform, driving ability, than 15mA.6, the ..
DESCRIPTION:Liquid level sensor is using infrared optical principle, the detection of liquid level, liquid level signal through the optical transmission, conversion to electrical signals for output, voltage signal collected by the sensor for level discrimination, the sensor has the advantages of..