0-24V Top Mosfet Button IRF520 MOS Driver ModuleProduct parameters:Size: 33.4 * 25.6MMVoltage: 3.3V, 5VPort: the digital quantity levelThe output load voltage: 0 to 24VThe output load current: < 5A (more than 1A need to add heat sink)Platform: the Arduino, MCU, ARM, raspberry pie The pr..
MOSFET is an electronic device having a good switching characteristics, is widely used in the electronic switch circuit needs, such as switching power supplies and motor drives, and a lighting dimming.The circuit is connected at one end of the wire is slightly controlled some trouble. To control a 1..
Description:• When delivering, the potentiometer is removed and put into the shell, so as
to prevent damage to the product during transportation.
• when wiring, pay attention to the power supply positive and negative must not
reverse connection, reverse connection is equivalent to a short cir..
Mosfet is an electronic device having a good switching characteristics, is widely used in the electronic switch circuit needs, such as switching power supplies and motor drives, and a lighting dimmingUse this module with for arduino electronic building blocks 4 irf540 mosfet switches use the same, b..
Description• DM420 is a type of two-phase hybrid stepping motor driver. The driver voltage
of which is from 12VDC to 36VDC.
• It is designed for use with 2-phase hybrid stepper motor of all kinds with
20mm to 42mm outside diameter and less than 2.0A phase current.
This circuit that it adopts..
The DM542C is a fully Lead shine digital step motor driver developed
with advanced DSP control algorithm based on the latest motion control
It has achieved a unique level of syst..
DM556 Digital Stepper Motor Driver 2-Phase 5.6A 256 Subdivision For 57 86 Stepping Motor Replacement Stepper Motor ControllerSpecifications:Input power: 24 to 50V DC power supply, the capacity is not less than 200VA, the typical value is DC 36VOutput current: 1.0A to 4.2A, 8 levels adjustable, 0.5A ..
The Dual Servos Knob Serial Port Control Board MG995SG90 Steering Gear
Debugging Module is a plug-and-play, easy-to-use servo controller with knob
adjustment, reply function, serial command control, and three servo control
L298P PWM Speed Controller Dual High-Power H-bridge Driver Bluetooth Interface L298P Motor Shield BoardTechnical Specifications:1.Logical part ofthe input voltageVD: 5V2.Drivenpart of the inputvoltageVS: VINInput6.5 ~ 12V, PWRIN4.8 ~ 35Vinput3.Logicalpart of the workcurrentIss: <36mA4.Drivenpart ..
Description• Large size range and large LED screen, standard size, easy to install.
• suitable for detecting the speed of every type of motor.
• Strong anti-interference ability, can precisely test the rpm value for the
• Equipped with hall sensor, has good stability, high measurement..
TB6600 4.5A Stepper Motor Driver Board Controller Replace TB6560 DC 10-45VMaterial: Metal and plastic.Operating voltage DC 10V-45V.Recommended to use DC32V power supply switch power supply.High-speed optical coupling 6N137, ensure high speed without losing step.The use of high current, high voltage ..
Specifications: This drive is an upgraded version of the TB6600, the breakdown of heightening to 32 segments, for high segmentation purposes. Applicable stepper motor: 42,57,86 type of 2-phase 4-phase (4-wire 6 wire line 8)Features: 1, 9V-42V DC power supply; 2, H-bridge bipolar constant-phase flow-..
FEATURES:1.2 HG7881 chip on board motor control. 2.The module can simultaneously drive two DC motors or a 4-wire two-phase stepper motor. 3.The module input voltage: 2.5-12V 4.Each channel has a 800mA continuous output current capability. 5.PCB dimensions: &nb..
The ULN2003 is a monolithic IC consists of seven NPN darlington transistor pairs with high voltage and current capability.
It is commonly used for applications such as relay drivers, motor, display drivers, led lamp drivers, logic buffers, line drivers, hammer drivers and other high voltage cu..
DRV8833 Dual DC Motor Driver Board Module 2 Channel 3V-10V 1.5A Driver Board ModuleSpecifications: Driver DRV8833 can control up to two DC motors or one stepper motor with a constant current of 1.5 A (peak 4A ).The motors are controlled, independently by means of PWM signals the direction of ro..